Cable Techniques - Camera DC Cables

DC Camera Cables

Hirose-4 Connector Shell Our DC power cables are used to power Lectrosonics receivers from various camera models that incorporate a Hirose 4-pin socket. All Hirose 4 equipped Battery Bud cables are carefully handcrafted to the highest standards using only premium components. The quality and durability of interconnect cables powering receivers off your camera is of tremendous importance for trouble free operation and the well being of your valuable gear. We use a molded, coax equipped ultra-flexible cable that is not hard and stiff like typical DC cables - which are prone to split and break prematurely.

Cable Techniques DC cables can be used with devices equipped with a Hirose 4 output that complies with the relevant standard for our industry: Pin-1 Ground, Pin 4-Hot. This of course also includes our Battery Bud II, Hawk Woods systems and the extra DC outputs on the PSC Alphamix mixer for example.

Specifications

Compatible With

Length: 9”

Lectrosonics portable receivers like UCR401, UCR411A etc. and Lectrosonics ISO9VOLT & SMBATELIM Battery Eliminators. Also for other devices with same DC socket specifications.

Connectors: Hirose 4-pin to Right Angle coaxial barrel

5.5 mm barrel diameter
14 mm barrel length
2.1 mm internal diameter

CT-CAM-9

To power a Lectrosonics receiver on a camera equipped with Hirose 4-pin DC socket

Specifications

Compatible With

Length: 8” & 9”

Lectrosonics portable receivers like UCR401, UCR411A etc. and Lectrosonics ISO9VOLT & SMBATELIM Battery Eliminators. Also for other devices with same DC socket specifications.

Connectors: Hirose 4-pin to Right Angle coaxial barrel

5.5 mm barrel diameter
14 mm barrel length
2.1 mm internal diameter

CT-CAM-8/9

To power (2) Lectrosonics receivers on a camera equipped with Hirose 4 DC Socket

Digital Microphone Cables for Sound Devices 788T

Our premium XLR-3F to DE-15 digital cables are used to input digital microphones like the Schoeps SuperCMIT 2U into a Sound Devices 788T. The 788T encompasses the necessary features needed to use a digital microphone like the Schoeps SuperCMIT in the field.

The digital input section of the Sound Devices 788T is located on the rear of the recorder via a DE-15 Multi-function connector. Our digital AES/EBU cables use premium components such as Mogami W3080 110 ohm AES/EBU cable and Neutrik XX Series connectors with gold pins.

CT-DE15/1

Specifications

Length: 30”

Connectors: Neutrik® XX Series 3-pin XLR-F to DE-15

Cable: Mogami® W3080 110 ohm Digital AES/EBU cable, 5mm diameter with ultra-flexible PVC jacket

Compatible with

Sound Devices 788T DE-15, 15-pin Multi-function connector on back of unit. To input of a single AES-42 digital microphone such as a Schoeps SuperCMIT 2U into Sound Devices 788T. Can also be used for input of any AES/EBU digital audio signal into a 788T.

Input Channels: Wired for Input channels 1,2 on 788T

Note: With a Schoeps SuperCMIT 2U the DSP-derived signal will go to channel one and the unprocessed shotgun signal will go to channel 2.

CT-DE15/2

Specifications

Length: 2 x 30”

Connectors: Neutrik® XX Series 3-pin XLR-F to DE-15

Cable: Mogami® W3080 110 ohm Digital AES/EBU cable, 5mm diameter

Compatible with

Sound Devices 788T DE-15, 15-pin Multi-function connector on back of unit. To input of a pair of AES-42 digital microphones such as the Schoeps SuperCMIT 2U or CMD 2U into Sound Devices 788T. Can also be used for input of any AES/EBU digital audio signal into a 788T.

Input Channels: Wired for Input channels 1,2 & 3,4 on 788T

CH 1,2 = Yellow
CH 3,4 = Red

Download Digital Microphone Cables for Sound Devices 788T Data sheet